溶液浓差能驱动的逆电渗析反应器制氢实验研究

低品位热能制氢技术首先是将热能转换为溶液浓差能，然后通过逆电渗析（RED）反应器将溶液浓差能转换成氢能。为了验证RED反应器能将溶液浓差能转换为氢能，探索关键运行参数变化对能量转换过程的影响。设计了一个由40个膜对所构成的RED反应器，以NaCl水溶液为工作溶液，NaOH水溶液为电极液的制氢系统。通过改变浓/稀溶液入口浓度，溶液过膜流速以及输出电流来考察对RED反应器产氢率、制氢效率和能量转换效率的影响。实验结果发现，浓/稀溶液入口浓度，过膜流速变化均会影响RED反应器的输出电流。在外电路短接条件下，输出电流越大，反应器产氢率和制氢效率越高，但能量转换效率越低。     

铜浮选专家控制系统设计与应用

针对国内某选矿厂铜浮选工艺泡沫速率不稳定,精矿品位波动大,回收率不理想等特点,设计了一套浮选专家控制系统,该系统结合泡沫影像分析技术,在线品位分析技术,PID控制与模糊逻辑控制技术。系统架构简明合理,逻辑层次清晰有效,投入运行一段时间后,在不同原矿品位前提下,都能实现稳定泡沫速率,减少精矿品位波动,提高回收率等指标优化,同时药剂添加量也有明显减少。这表明该系统运行效果良好,值得应用推广。     

Effect of cellulose acetate/cellulose triacetate ratio on reverse osmosis blend membrane performance

Surface functionalization and modification including the grafting process are effective approaches to improve and enhance the reverse osmosis (RO) membrane performance. This work is aimed to synthesize grafted/crosslinked cellulose acetate (CA)/cellulose triacetate (CTA) blend RO membranes using N-isopropylacrylamide (N-IPAAm) as a monomer and N,N-methylene bisacrylamide (MBAAm) as a crosslinker. The morphology of these membranes was analyzed by scanning electron microscopy and their surface roughness was characterized by atomic force microscopy. The performance of these membranes was evaluated through measuring two major parameters of salt rejection and water flux using RO unit at variable operating pressures. It was noted that the surface average roughness obviously decreased from 148 nm for the pure CA/CTA blend membrane with 2.5% CTA to 110 nm and 87 nm for the grafted N-IPAAm and grafted/crosslinked N-IPAAM/MBAAm/CA/CTA-RO membranes, respectively. Moreover, the contact angle decreased from 51.98° to 47.6° and 43.8° after the grafting and crosslinking process. The salt rejection of the grafted CA/CTA-RO membrane by 0.1% N-IPAAm produced the highest value of 98.12% and the water flux was 3.29 L/m²h at 10 bar.     

基于分段加权的反向稀疏跟踪算法研究

为提高稀疏表示跟踪模型性能，提出一种分段加权的反向稀疏跟踪算法，将跟踪问题转化为在贝叶斯框架下寻找概率最高的候选对象问题，构造不同的分段权重函数来分别度量候选目标与正负模板的判别特征系数。通过池化来降低跟踪结果的不确定性干扰，选择正负模板加权系数差值最大的候选表示作为跟踪结果。实验表明，在光照变化、遮挡、快速运动、运动模糊情况下，所提出的算法可以确保跟踪结果的准确性和鲁棒性。     

浮选机运输区的结构特征的测试研究

浮选机内各动力学分区的流动特征复杂。本文选取单槽容积0.2m3KYF型充气机械搅拌式浮选机为研究对象,采用PIV测试技术开展运输区的结构特征和动力学特征的研究。研究表明运输区在半个槽体的取截面内的轮廓形状整体呈现为左边为直线,右边折弯线,上下近似直线的近梯形结构,具有高度和宽度两个主要结构特征。运输区轮廓边界处的动力学特征存在明显差异。本研究加深了对浮选机运输区特征的理解,有助于通过调控运输区特征方法解决大型机械搅拌式浮选机粗粒矿物回收率低的难题。     

郴州某复杂硫化铅锌矿阶段磨浮试验研究

针对郴州某复杂硫化铅锌矿资源的性质特点,采用铅快速浮选后尾矿再磨再选的阶磨阶选工艺,较好地实现了铅锌的高效浮选回收。研究了磨矿方式、捕收剂和调整剂种类及用量等因素对该矿石浮选的影响,确定了最佳浮选条件,通过小型闭路浮选试验,得到了铅品位60.05%、回收率89.63%的铅精矿和锌品位47.01%、回收率88.14%的锌精矿。     

A mixed collector system for phosphate flotation

Flotation has been used in industry for more than a half century as the primary technique for upgrading phosphate. While the flotation of phosphate was inefficient when oleic acid was used alone as a collector, therefore a mixed collector of oleic acid (HOl), linoleic acid (LA) and linolenic acid (LNA) was employed to improve the recovery of phosphate flotation. The batch flotation results showed that the optimal composition of the mixed collector was 54 wt.% HOl, 36 wt.% LA and 10 wt.% LNA. Additionally, the effect of pH on the mixed collector application was studied while considering the surface tension, contact angle and micro-flotation. The results showed that the mixed collector should be used at a pH of 9.5. Above a pH of 9.5, the adsorption of fatty acids dimers on the apatite surface hindered phosphate flotation. The influence of the mixed collector assembly on apatite flotation was also investigated. It was demonstrated that due to its low critical micelle concentration, a sufficiently hydrophobic apatite surface could be generated at a collector concentration of 60 mg/L. In addition, zeta potential experiments suggested that collector adsorption was governed by chemisorption. FTIR and XPS spectra studies further indicated that the chemical reaction involved the carboxyl groups of fatty acids and Ca species at the apatite surface for each fatty acid in the mixed collector.     

某含锌锡多金属硫化矿石锌浮选试验研究

某含锌锡多金属硫化矿石Zn、Sn、Fe、S含量分别为6.04%、1.05%、29.33%、19.08%，锌主要以铁闪锌矿、闪锌矿的形式存在，锡主要以锡石的形式存在，铁主要以黄铁矿、磁黄铁矿等形式存在，其中的金属矿物共生关系密切，相互包裹现象普遍。为确保不影响后续选锡，对锌浮选流程进行了试验研究。结果表明：矿石在磨矿细度为-0.074 mm占80%的情况下，采用预先脱硫—锌硫混浮再分离流程处理，在选择硫酸铜为锌矿物活化剂、丁基黄药为捕收剂、松醇油为起泡剂、石灰为黄铁矿抑制剂的情况下，经1段脱硫、2粗1扫锌硫混浮、1粗2精锌硫分离，锌硫分离精选尾矿与锌硫混浮扫选精矿2次精选后锌硫分离，最终获得锌精矿Zn品位47.06%、回收率90.76%，试验指标良好。